Howdy, Stranger!

It looks like you're new here. If you want to get involved, click one of these buttons!





Chevy Tahoe

1244245247249250308

Comments

  • aacukaacuk Posts: 16
    I have a 1999 2 door Tahoe, 5.7 vortec LT.

    Question :- If I change my back axle ratio do I also have to change anything on the front end?

    Thanks in advance Roy.
  • sebring95sebring95 Posts: 3,231
    Question :- If I change my back axle ratio do I also have to change anything on the front end?

    Absolutely! Unless you never plan to lock it in 4x4 again!
  • aacukaacuk Posts: 16
    Thank you for the reply, this could be the start of sorting out my problem.
    When my Tahoe left the factory it was fitted with options 'G80 positraction, limited slip - GT4 3.73 Ratio', at some time in its life prior to leaving the USA the complete rear axle has been changed for a conventional axle of unknown ratio. (There are NO IDENTIFICATION MARKINGS on the axle now fitted. 1. How do I determine what the ratio is? 2. If it is not 3.73 ratio could this be the cause of a loud banging/grating sound (like gear teeth jumping) when I select 4x4?
    It is OK in 2 wheel drive. 3. What would be the easiest/cheapest to change, front or rear ratios? :cry:
  • rmarutrmarut Posts: 8
    I recently purchased a used 2002 Yukon (Wanted a Tahoe but got this Yukon instead) I had it for a few months and one day I noticed bubbles in the paint along the folded seam on the rear hatch... this caused me to look at all the seams on the doors (at the bottom) and the hood... They all had the same rust issues. I didn't look as closely as I should have when I purchased it... as it was a "Certified GM Used Vehicle..." to make a long story short... I had to fight a little to get the local GM body shop to fix it... or should I say post pone the end result... It has only been 2 months... and the rust issue is back on the hatch... I started looking at other Tahoe's and Yukons to make a trade to get rid of this rusty vehicle... only to find that everyone I looked at... was in the same condition... I looked at 3 2003's and 1 2002. I even checked my friends 2003 Chevy truck... and his seams in his door are doing the same thing and he does not drive his truck in the winter and only has about 15,000 on it... he keeps it more for show than anything. Just wondering if anyone else is having this problem. Thanks.
  • piercemanpierceman Posts: 47
    Aren't our hatches aluminium?
  • jlflemmonsjlflemmons Posts: 2,240
    I don't know where you are geographically, but I don't think I have ever seen rust on a GM truck or SUV here in central Texas. And there are a lot of them around!
  • rmarutrmarut Posts: 8
    These vehicles have all been looked in northern OH, PA and NY. I realize we are in the "rust belt" but on a vehicle that is only 2 years old... and not driven very much... to have rust in the seams of the doors... it just isn't what one would expect... don't get me wrong... I love the Yukon and Tahoes... best looking vehicle on the road today.. I like everything about it... except the fact that it has rust issues. My other GM products never had these issues even when they were 7-10 years old. Thanks.
  • aa555zzaa555zz Posts: 55
    My 2002 Tahoe does the same thing and the oil is at the correct level. However, mine does not leak enough fluid to dip onto the floor. The front axle assembly does not use transmission fluid. It uses gear oil. If your front axle oil has been changed, make sure they used the correct oil. Transmission fluid is red in color. Gear oil has a distinct smell.
  • bradstahoebradstahoe Posts: 1
    I may be one of the millions with this complaint...but my dealer keeps reassuring me there is nothing wrong with my 01 tahoe LT 4x4 transmission. I have a very frequent hard shift from first to second gear-regardless of the terrain (coupled with the "clink" noise). When the tranny is cold, it even lunges a little when trying to shift. At times the transfer case seems to have a vibrating noise coming from it. The dealer has checked it all out, and said nothing is loose. Anybody with this same "complaint" about hard shifting and what can I do?
  • sebring95sebring95 Posts: 3,231
    Wow, yeah the symptoms you describe could happen due to having different axle ratios on the front & back. The easiest fix IMHO would be to swap back a facory rear axle (locking or not doesn't matter, just go 3.73) since the front hasn't been changed.

    There's a way to figure out the ratio, but you'd have to find the specs. You should be able to match rpms & speed to a specific rear ratio. I don't know of the top of my head how to do this or where to find the factory specs. Sometimes they're listed in service manuals.
  • dynastydynasty Posts: 2
    I bought a 2004 Tahoe 4.8 L last November. My wife uses it primarily in the city. We only have about 4k miles on it but the gas mileage really sucks. I have been reading about this on the boards but I think my mileage is so bad that something must be wrong. I am only getting about 11.5-12.5 MPG. Has anyone else seen their mileage this bad? We do use it on the highway about 20% of the time and the mileage remains about 12mpg. What can be the cause of this? What are some of you experiencing as far as miles goes? Please give me some feedback. I love the vehicle but the mileage really should be this bad should it?
    Thanks,
    Fred :confuse:
  • sanandtonsanandton Posts: 342
    I have had 2 Tahoes 2003 LT, and 2004 Z-71. My LT was 2wd and it had a problem of a delayed shift from 1rst to 2nd gears. It would begin to try to shift, but be slow about making the entire shift, then suddenly a distinct bump would occur as it finally made the shift. It felt like someone had tapped my bumper from behind. Never got it fixed, so traded it in when it got 36k miles for my 2004 Z-71.

    The Z-71 is 4wd and it has always had what I call "slop" in the drivetrain. It feels like my old 76 Camaro when the Universal joints would wear out. It shifts harshley especially when not under load, such as letting off of the accelerator in the parking lots. Frequently there is a distinct Metallic "Clank" with the shift as well. My dealer installed some extra lubrication yoke which really did not fix it. At the same time they reassured me it is a common issue. Almost common enough to reassure you you have a GM truck just by having the problem.
  • aacukaacuk Posts: 16
    Thanks for the info Alan, not many American axles knocking about here in the UK so I will order a new 3.73 ring & pinion from my local American parts dealer & swap it for the one that is in there. ;)
  • jay_24jay_24 Posts: 536
    mpg could be that bad. depends on your driving style and conditions. If you have lots of stop-go conditions and seldom hold a steady pace it could be 11mpg. We get about 12mpg (80% city) in the winter. Come summer and warmer temps it comes up to about 15 or so. Straight highway its quite good at 18 to 19mpg.
    Check your tire pressure. I tend to run a pound or two above recomended pressures. being just a pound low can affect mpg.

    --jay
  • arriearrie Posts: 312
    I think you just must have 4 sensors in the vehicle all reading high enough pressure to keep warning off. I don't think there is a way to disable it if one tire with sensor goes flat other than fixing the tire.

    Perhaps this is good so it makes you go and fix the tire sooner?!?

    Arrie
  • arriearrie Posts: 312
    Dynasty,

    I have a 2004 Tahoe but with 5.3 l engine. This might make a difference but perhaps not.

    I wrote about this in my reply to dubois. You can find it on page 260 in this forum.

    I can now tell about my gas mileage that it definitely is at least 18.5 mpg driving on interstate highway on 70 mph speed limit area at speed that most everyone seems to drive. Before I got it fixed (as explained in my reply to dubois) my gas mileage was down at 13 - 15 mpg at these speeds.

    If I drive on a highway at 60 mph speed my gas mileage goes up to 21 - 23 mpg.

    I am absolutely sure that the engine in my Tahoe (like in all same model Tahoes) has a design problem with the crank shaft position sensor which causes this sensor to read wrong as it heat up with hot engine oil splashing on it.

    There are a couple easy things you can do. One is to go and have good people in an Auto Zone store to read codes from your vehicle's computer. It probably does not have any but have it done anyway.

    After codes are read have them to read I/M monitors. They should all say READY (other than the NOT APPLICABLE ones). I had a problem with EVAP SYSTEM not being ready before I changed my crankshaft position sensor. If any of the I/M monitors is showing NOT READY there is something wrong and usually it means that fuel consumption goes up as the computer in the vehicle goes in a pre-programmed control mode where it does not use signals from different sensors like oxygen sensors for fine tuning fuel injection in the engine.

    But, as I learned in with my Tahoe, check your engine oil level. If it shows full or above full mark drop it down a little bit. The dip stick in my vehicle has an area cross-hatched that is 1.5 inches wide. The manual says oil level in any point inside this area is fine so I dropped mine from higher than full mark down to half way and this simple procedure improved my gas mileage by about 2 mpg! Hard to believe but true.

    Read my reply to dubois and see what you think.

    Arrie
  • aa555zzaa555zz Posts: 55
    This web page will explain how to determine your axle ratio. http://www.jedi.com/obiwan/jeep/misc/gearratio.html
  • brian77711brian77711 Posts: 1
    I have the same problem in a 99 Suburban. Two dealers said it was the yoke and inserting grease was the only solution--it sounds like a major engineering flaw and GM will not recall! They also said a new yoke would not fix it. Do you know anything else?
  • aacukaacuk Posts: 16
    Thanks a million James, I found this site really helpful.
  • philryanphilryan Posts: 1
    I have had what I believe is a similar problem for the past 35,000 miles and the service mechanic gave me a copy of a service bulletin that stated that this was a normal situation on "some" vehicles. Other than the occasional clunk during low speed shifts, I've had not trouble in almost 59,000 miles.
Sign In or Register to comment.