Howdy, Stranger!

It looks like you're new here. If you want to get involved, click one of these buttons!





Toyota Camry: Problems & Solutions

1207208210212213246

Comments

  • I have an 02 Camry, about 54,000 miles. Just found out I need a new timer/drive belt. According to the maintenance books, this belt is "checked" at 60,000 miles. Is this normal based on city/freeway driving?
  • wwestwwest Posts: 10,706
    Any dealer will also sell you a new engine if you're dumb enough to believe him when he says you need one.
  • 210delray210delray Posts: 4,722
    Is this a timing belt OR a drive belt (big difference between the two, costwise). If you have a 4-cylinder Camry, the timing belt was replaced by a chain starting with 2002 models, so it never needs replacement. On the V6 model, the timing belt should be replaced every 90,000 miles, and this will cost at least $200, mostly for labor.

    If it's a drive belt, it should be checked periodically for wear, cracks, and proper tension, but you can do that yourself by looking at it and pressing against it with your finger between two pulleys. (The engine must not be running, of course.) Or a service shop can do it at the major maintenance intervals for essentially no extra cost.
  • I just test drove a new camary and felt that shifting gear in transmission is taking too long and searching compare to older camaries with 4speed transmission it feels difference, any comment? id this normal?
  • bildowbildow Posts: 100
    I have a 2005 camry and it does search due to the transmission is now complety run by a computer. On the new camry it is drive by wire no throttle cable and no kick down cable( passing gear) everything is done by electronics. It just takes a little getting use to, I also have the five speed transmission and found it's better to leave it out of overdrive in town and bumper to bumper traffic. The new transmissions in the camry are slow in shifting but they tell me this is the way all the new trans work. Also the new transmissions take a special oil due to the way they are make toyota uses type 4 transmission fluid so don't use dexron 2 or 3 type when you change your trans fluid at 30,000 miles. :shades:
  • jay35jay35 Posts: 1
    My wife's 92 Camry ignition lock cylinder developed a rough feel when using newly-cut ignition keys. The lock cylinder would rotate to Start position but would not start car. It felt like neither of the new keys were turning smoothly, nor completely, and I suspect the keys damaged pins in the cylinder.

    Now when we try to original Toyota key, the lock won't turn at all. Based on mssgs posted here, I have tried pulling hard on the locked steering wheel in both directions, changing tilt on steering wheel, and have tried turning the lock with transmission shifted to Neutral using manual override button, but key still will not turn at all.

    I think the ignition lock needs to be replaced, but cannot turn key to ACC position to depress release button for lock removal. How can I get key to turn to ACC position? Anything else suggested in troubleshooting would be appreciated.
  • haefrhaefr Posts: 600
    Part of the computerized transmission control logic parameters are algotithms which allow the computer to tailor itself to the particular driving habits of the principle driver. Doing so takes time - as much as several months. Coincidenatlly, new band and clutch facing materials are not burnished to their final finish against the parts with which they're in contact during shifts. It would be perfectly logical for the manufacturer to set the shift patterns up on the "sluggish" side of permittable initially to allow an easy break-in of these clutch facings over the first 100 or so miles. The upshot is that, once broken-in, if the driver routinely engages in "sport" greenlight-grand-prix starts, the transmission will "learn" to accomodate with quicker shifting patterns. Likewise, the reverse is true for more sedate drivers. Once the driving style of the principle driver is established, further refinements are ongoing to compensate for the inevitable wear of the friction facings in bands and clutches. In other words, the tranny will continue to maintain the "learned" shift quality patterns without periodic servicing adjustments until it tanks. If the car changes ownership prior to meltdown, the tranny will learn the habits of the new owner over time - or faster if the TCM fuse is removed or the battery's negative terminal is disconnected for several minutes.
  • Thanks for the insight. I do have a V6 and its both the timing and drive belts according to the repair recommendation. I have a friend who experienced a similar repair at about 60,000 miles or so. Is the water pump a factor in any of this??
  • Hey guys!! I got a prob that I was wondering if you guys could help me with!! On my automatic seat belts (shoulder Strap) on the drivers side has been having problems, before when opening the door, it would grind along the tract and stop, this didn't bother me too much, but now its stuck, it will not move back what so ever to cover my chest, ive even tried pressing that black rubber thing on the inner door and still nothing. my drivers side door is the opposite, it stays back and wont move forward which is fine cause it covers my chest when im passing a cop lol, but I have no idea what the problem could be!! Can you guys please help a guy out, id really appreciate it thanks

    Big Daddy
  • joe122joe122 Posts: 68
    Indeed, but it's a bit more complex than that. For example this algorithm:

    "The KGPD algorithm is composed of a driving environments and driver's intentions estimator, the shift schedules for each typical driving environment and driver's intention situations, and an inference logic to determine the most proper gear position for the present situation. The estimator identifies the driving environments and features of driver's intentions, which are divided into some typical patterns. Based on the identified results, the gear-position inference algorithm calculates the best gear position at the moment. In fact, the method just simulates the course of a driver's making gear-position decision when driving an automobile with manual transmission. The test results show that the AMT with the method gives less unnecessary shifting, conducts more proper gear positions, and behaves better in subjective assessment than that with the method that is directly based only on automotive state parameters."
  • Hey, got a hand-me-down 1995 camry from my grandparents. But when i got it they notified me that the cigarette lighter had stopped working suddenly when they had one of those little car vaccums plugged into it. But they didn't bust the fuse cuz the fuse is linked to the radio too which is still working and there are no burnt fuses. Friends have suggested that the vaccuum may have been pushed in too far or that the lighter assembly may have overheated and something behind where i can see may have melted. i don't want to start taking the whole thing apart or paying someone to do so unless i have a better idea of why the lighter just doesn't work at all.

    Also, the antenna in recent years had stoppped retracting when it was turned off... over the summer i noticed that if you someone pushes it down a little when the antenna motor starts up, it retracts and then will extend the next time the car is started, making a very loud grinding noise when it's done extending. Only problem is, you have to go back and push it down again to get it to retract again.

    If anyone has had these problems, or knows anything that might help me figure out what needs to be fixed before i pay through the nose for someone to open everything up, i'd really appreciate the info!
  • I had same problem with my '03 camary when it was new pull me to right, after return to dealer and they spent hours to inspect every little detail they found the problem, guess what was that? just tire pressue!!! check that
  • so in other word it means that it takes a while that new transmission logic get used to new driver and shifting gear smoother?
  • siwelsiwel Posts: 2
    turtlejames,

    Have you figured out any solution or even the cause of your sloshing sounds? I took the car to a Toyota dealer and they had a sr. technician look at it. His recommendation was to tear apart the dash and look around. That sounds like $$$$ to me. Even though the car was under warranty, they would not confirm this would be covered. I called Toyota USA 800.331.4331, and spoke to Andrea. She had no clue, and discussed with the other techies. They had no clue either. Nobody at Toyota claims to ever had heard of this problem. So far I have experienced no problems other than annoyance.

    cam2003
  • I own a 2000 Camry. Unfortunately when I bought it, it didn't come with an owners manual. My rear window defroster isn't working. Can anyone tell me what fuse or relay the defroster works off of? Also, my heater fan only works on high speed. Could this be a fuse or relay (if so, which one?), or a more serious electrical problem?
  • wwestwwest Posts: 10,706
    Each time the ignition is turned off all driver related memory parameters are erased. Within a fairly short period of a "new" driver having started the car in motion the driver will have been automatically categorized in 1 or 4 driving style/types. After that the driver "parameters" will continue to be monitored and eventually categorized more finely into 1 of 16 driving styles/types. Thereafter a running record of (ONLY) the past three minutes will be kept in memory and the driver will be re-categorized "on the fly" if the need arises.

    How else could the rental fleet "work"?
  • user777user777 Posts: 3,341
    this is mere speculation, but i think the cigaretter lighter is fused on both legs of the circuit: HOT side and ground. do you have a manual? if so, check to see if there is a 10A or 15A fuse in the fuse compartment specifically labeled for the cig lighter. that would be the one for the HOT side, which by the way, may not be operational unless the switch is in ACC or ON positions...not sure.

    then it's possible there is also an "in-line" fuse in an "in-line" fuse holder, behind the dash going from the ground side of the cig lighter to vehicle ground. you'd have to reach around back there (or try moving the seats and using a mirror and flashlight). maybe removing the cig tray will make the wiring accessible. can't remember the configuration of the camry.

    i doubt very much the radio and the cig lighter are on the same circuit from the fuse compartment.

    btw, even if a fuse looks like it is OK, you don't know until you examine it closely, and perhaps check it with an ohm meter.

    try to see if there is two fuses. best of luck.
  • my 2oo1 camry, with 110,000 mls cuts off or rough idles when coming to a stop or slowing down..the problem is intermittant so troubling shouting is difficult.. there are no codes, although on one occation it hard started and ck. eng light came on with p0300 code/cylinder misfire..... it will act up this week then may not see the problem until maybe next month...any help
  • yes, ihad the same issue with my 4runner anntena, you will have to buy an, antenna cause the vinyl pickup coil to retract and extend the antenna is broken... once u can hear the motor running when u switch on then the motor is ok.i installed mine myself, its not a bad job if u have some confidence... good luck..
  • I have the same problem with my Camry 97 XLE. The engine won't start easily in cold weather even though the battery is fine. Could you tell me how do I locate the coil and how to replace it? thanks!
This discussion has been closed.