did yr mechanic check the oxygen and air fuel sensor? my 2004 sienna didn't pass inspection in 2009. i paid $2200 to fix it..... fixed the sliding door $2300 in 2010....they said the steering wheel has problem now.....i'm still thinking should fix it or not, it costs $2500..... what the "xxxk"sienna.......
engine light came on,vsc and trac off lights came on too,i took it to the dealer toyota capistrano where i bougth it new now its 34000 miles in it,the whole day it sat there in the afternoon they said its done so i went home as soon i got out of the dealer the same lights came back again,so turn around and take it back inside the service yard they said they dint find the other problem they change one part but they said onother park needs to be change how come desame problem did they change the wrong part ? or they dint do anything,but i've heard once you reach 30000 miles this automatically come out evry 30000 and it just need to reset something whatsoever is that,thers no actually parts to be replace am i correct,pls give me information about this problem.
is the gas cap has something to do with that damn indicator warning light what for or its just made like that so that they can drain money ,time,on the costumer it doesnt make sence a loose gas cap can do damage just like that they should correct this problem,whoever idea is that.
I seemed to have a battery problem today, was able to get a boost and get started. However, I was unable to accelerate beyond 2000 rpm. The "check engine", "vsc", "trac off" lights came on. I tested the battery, replaced it, lights are still on, still no acceleration. Cannot drive over 25mph.
I seemed to have a battery problem today, was able to get a boost and get started. However, I was unable to accelerate beyond 2000 rpm. The "check engine", "vsc", "trac off" lights came on. I tested the battery, replaced it, lights are still on, still no acceleration. Cannot drive over 25mph. This is a 2006 Sienna.
I have a 2004 Toyota Sienna Van with about 140,000 miles on it. My check engine light came on for about a week before I got it checked at a local repair shop while getting an oil change. Van was driving just fine. They pulled a code P0430 - catalyst system efficiency below threshold (bank 2). They had to order the part, so I have continued to drive it. Later that same day, the light went off. The mechanic says he did not reset the computer.
My question is - when you get this code, how definite is it that the catalytic convertor is bad? How long can I wait to replace it? Fortunately, I went immediately to get an emission test done and the van passed. So I can get my tags with no problems next week. It is suspicious that the light went off on its own. I don't want to spend money on this if it is not necessary. But, I don't want to get stranded with kids in the van. The only thing I can think of that was different, is that I was overdue for an oil change. But, not enough overdue that the "maintence required" light came on.
I have a 2005 Sienna and on several trips usually on the freeway or highway to Las Vegas while traveling at higher than usual speeds for a time the check engine light has come on. Later on it went off after a few days of normal driving. I do not believe this has anything to do with the oil change schedule. When i get the oil changed at Walmart every 5,000 miles, I always remind them to zero out the maintenance light whether or not it has come on.
The maintenance reminder system and the engine light (part of the OBDII system) are totally separate. The reminder system is on time & mileage, On Board Diagnostics is the federally mandated emission controls watchdog that monitors systems to ensure a clean exhaust.
So, on to your code... The code you logged was from a reading by the rear oxygen sensor, located behind the catalytic converter. While the front O2 sensor plays a real feedback role in regulating mixture, the rear sensor is just a tattletale device ratting you out to the EPA as a person of low moral character (just kidding...). It is suggesting that there is a real problem, but in no way impacts driveability, emissions, etc. If it wasn't that many states will not grant inspection stickers if this is a hard code, you could drive on forever with perhaps minimal impact, other than a sooty exhaust.
Now in reality, continuing to drive this way could eventually result in a clogged cat, which could degrade performance. So you do want to know why, and get it fixed.
Why did the light go out? Your system has several 'tiers' of code notation, ranging from "something happened, but it might just be an aberration", all the way up to "DEFCON 5" Armegeddon.
"Something happened" codes can go away in as little as 3 'drive cycles' (basically cold starts with some driving). More severe but fixed items go away after 40 cycles.
Sounds like your rear sensor might have sniffed out a one time burst of rich mixture, and it went away. Time will tell if it will return. Summer/Winter crossovers are common times for this to happen, as gasoline is 'reformulated'. Long drives with one pedal position & constant speed followed by a sudden off ramp (a big change in system status) have been known to trigger it on marginal systems.
Proper diagnosis can be difficult but it is essential. It could be a degrading cat, a dirty or compromised O2 sensor, bad wires or connections, or a computer issue. If you don't know what is broken, fixing it can be very costly!
Hi, I'm habving the exact same problem with my 2011 sienna. Did you find out what was wrong and how to fix it? I called the dealer and they weren't much help at all. The mechanic i talked to never heard of this happening before. aahhhrrgg. take care.
you seem to have the same i had recently ( i have the same car you have). i brought to toyota services and all theyb did is charged me a stupid over $400 and only changed a fuse on ETC( electrical throttle control ) and some others sunnessesary . do not make mistake like me.
i have toyota sienna 2006 with code p0430 ,i cleared it,repplaced it and came back on again after driving about 200 miles. I cleared it again it go on again after about 20 miles , i cleared i again and again. At one time the check engine light went off by itself without cleared . Any suggestion ,thank you very much.
Hello, Thank you for posting your experience with the 2004 Toyota Sienna ABS and Sensor issue! I know it has been a while... I just ran into this today, got the exact same answer from the toyota service as you got... and was wondering if the solution you have posted lasted, or any issues came back later... thank you for the info you posted! Looks like it could help quite a few people avoid spending major $$$ on an unnecessary repair!
I have a 2009 Sienna and it has happened twice for very brief periods. I will be driving along at highway speeds for extended periods and get an alarm. It is a beeping at about 2x per second accompanied a flashing indicator in the upper right portion of the dash near the maint req light. This was so brief (2-3 sec each occurrence) that I couldn't determine what exactly the light was that was blinking. Has anyone else experienced this and what was the problem/solution?
I've had numerous issues with my 2006 Sienna with only 21k on it. One has been erroneous warning lights. This morning another incident with the Check Engine-VSC-Trac warning lights suddenly coming on and staying on even after a few starts and stops.
Based on past experience I first check the internet for fellow sufferers to see if there isn’t a simple fix and an avoidance of the dealer. Sure enough this is yet another common issue. A loose gas or defective gas cap seems to be a common problem. Checked, but not my problem. Next seems to be a faulty oxygen sensor, e.g. dealer and money. After only 21k I didn’t think it was likely (or maybe it was hope it wasn’t likely).
Third most common is a recent tire change affecting the ABS and thus the Check Engine and VSC Trac lights which activate evidently to protect the systems. I did have to replace the front tires already, but that was some time and miles ago, so I doubted that was my issue.
Fourth, and way too common with Sienna’s, a faulty sensor reading. A solution to this possibility I found on fixya.com – disconnect the negative terminal on the battery for a few minutes. The lights are now off.
My Sienna is painted red; it should have been painted yellow for lemon.
i have an 02 Sienna and the engine light came on, had it scaned and the code came up P1135. A Air/ Fuel sensor bank 1 sensor 1 . I purchased the sensor from Autozone, put it in and the service engine light is still on with the letters VSC and tractin off light on. Any helpful advise out there.
You sound more expert than me, but my research on this issue indicates that it takes a while for the warning indicator to clear even after the issue has been resolved. Also the VSC and Trac Off always come on whenever the Engine light comes on as a precaution. Hopefully it will clear after a few on and off cycles.
You could also force a clear by disconnecting the negative for a minute or so and if it doesn't return all's good. Mine is still off after many on and off cycles and a couple hundred miles.
Unfortunately, part of your persistent problems may be related to your low annual mileage. Mechanical things and even electronic sensors 'like' to be used & cycled, and many short trips or days of sitting can have a negative impact.
I highly advise you to buy a code reader with a clear/reset function, and use that instead of disconnecting the battery. Some of your problems may be directly related to this practice, and Toyota has advised against doing this in multiple publications. TT-0086-11 is one of the more recent ones that list recovery procedures from poor driveability after a battery disconnect. These vehicles rely on 'learning' and stored values to compensate for age and wear. When you wipe the memory, you reset to original factory specs, and the vehicle can really be at odds with these values. Doing this wipes out idle settings, short and long term fuel trim, ignition timing, etc. This can result in false oxygen sensor (front A/F and rear O2) codes, or even converter degradation.
VSC & Trac *may* come on, depending on what the logged code is. It usually accompanies issues that impact driveability, and not necessarily just simple emissions issues.
Some codes set on a single incident, some after failing several tests in a sequence. Codes can go away in as little as 3 passing drive cycles, some remain up to 40.
I've not seen a code set just because of a tire change, although I suppose that earlier indirect TPMS could - especially if you have severely mismatched tires that result in a substantial rotational difference? I'd be interested to know more on this one.
I run with a laptop based system that is on the expensive side. I'm sure someone can chime in on their recent experience with a sub-$100 handheld unit. Sorry that I cannot be of help here.
I have a $99 or so Actron reader. It gives you the code and can reset it. Comes with a booklet to interpret codes but I search the internet instead. Does the trick, but very basic.
Sienna 2004...Just found out , the cel, vsc and trac off may come on if you change the air filter and disconnect the wire harness from the top of the filter housing. In this case it did throw air intake / mass airflow sensor codes.
My conclusion:
Any time you get a cel after disconnecting any wire harness while working on the engine,
it is a good idea to reset the cel first, and see if it is bogus, related to the disconnect before taking it to the dealer.
If there is a real problem, the cel will come back on.
For my 2006 Sienna, the check engine light and "VSC" light came on. The "TRAK OFF" did not come on. This was due to the gas cap. After the next fill up, the lights cleared up after 2 days.
I brought a used 2007 Toyota sienna CE and have been having issues with the check engine light coming on, and when the check light began to flash the car will be moving sluggish and when I get to a hill, the speedometer will be dropping but when am moving down the hill, it will be spending fine. But if I put off the engine and put it back on , it will be fine and will later come back on and start flashing again after some minute. I took it to a mechanic and the code reads misfire on cylinder 1. They replaced the coil and the sparkplugs and it will fine. After some minute I drove out from the mechanic it started again, and I went back and change all the coils and the sparkplugs, but the problem is still there. Please i need advice on what's is happening to my car. Thanks
Comments
Thoughts?
Thoughts?
My question is - when you get this code, how definite is it that the catalytic convertor is bad? How long can I wait to replace it? Fortunately, I went immediately to get an emission test done and the van passed. So I can get my tags with no problems next week. It is suspicious that the light went off on its own. I don't want to spend money on this if it is not necessary. But, I don't want to get stranded with kids in the van. The only thing I can think of that was different, is that I was overdue for an oil change. But, not enough overdue that the "maintence required" light came on.
I would welcome any words of wisdom. Thank You!
So, on to your code... The code you logged was from a reading by the rear oxygen sensor, located behind the catalytic converter. While the front O2 sensor plays a real feedback role in regulating mixture, the rear sensor is just a tattletale device ratting you out to the EPA as a person of low moral character (just kidding...). It is suggesting that there is a real problem, but in no way impacts driveability, emissions, etc. If it wasn't that many states will not grant inspection stickers if this is a hard code, you could drive on forever with perhaps minimal impact, other than a sooty exhaust.
Now in reality, continuing to drive this way could eventually result in a clogged cat, which could degrade performance. So you do want to know why, and get it fixed.
Why did the light go out? Your system has several 'tiers' of code notation, ranging from "something happened, but it might just be an aberration", all the way up to "DEFCON 5" Armegeddon.
"Something happened" codes can go away in as little as 3 'drive cycles' (basically cold starts with some driving). More severe but fixed items go away after 40 cycles.
Sounds like your rear sensor might have sniffed out a one time burst of rich mixture, and it went away. Time will tell if it will return. Summer/Winter crossovers are common times for this to happen, as gasoline is 'reformulated'. Long drives with one pedal position & constant speed followed by a sudden off ramp (a big change in system status) have been known to trigger it on marginal systems.
Proper diagnosis can be difficult but it is essential. It could be a degrading cat, a dirty or compromised O2 sensor, bad wires or connections, or a computer issue. If you don't know what is broken, fixing it can be very costly!
And that concludes tonight's lesson!
good luck
Based on past experience I first check the internet for fellow sufferers to see if there isn’t a simple fix and an avoidance of the dealer. Sure enough this is yet another common issue. A loose gas or defective gas cap seems to be a common problem. Checked, but not my problem.
Next seems to be a faulty oxygen sensor, e.g. dealer and money. After only 21k I didn’t think it was likely (or maybe it was hope it wasn’t likely).
Third most common is a recent tire change affecting the ABS and thus the Check Engine and VSC Trac lights which activate evidently to protect the systems. I did have to replace the front tires already, but that was some time and miles ago, so I doubted that was my issue.
Fourth, and way too common with Sienna’s, a faulty sensor reading. A solution to this possibility I found on fixya.com – disconnect the negative terminal on the battery for a few minutes. The lights are now off.
My Sienna is painted red; it should have been painted yellow for lemon.
You could also force a clear by disconnecting the negative for a minute or so and if it doesn't return all's good. Mine is still off after many on and off cycles and a couple hundred miles.
I highly advise you to buy a code reader with a clear/reset function, and use that instead of disconnecting the battery. Some of your problems may be directly related to this practice, and Toyota has advised against doing this in multiple publications. TT-0086-11 is one of the more recent ones that list recovery procedures from poor driveability after a battery disconnect. These vehicles rely on 'learning' and stored values to compensate for age and wear. When you wipe the memory, you reset to original factory specs, and the vehicle can really be at odds with these values. Doing this wipes out idle settings, short and long term fuel trim, ignition timing, etc. This can result in false oxygen sensor (front A/F and rear O2) codes, or even converter degradation.
VSC & Trac *may* come on, depending on what the logged code is. It usually accompanies issues that impact driveability, and not necessarily just simple emissions issues.
Some codes set on a single incident, some after failing several tests in a sequence. Codes can go away in as little as 3 passing drive cycles, some remain up to 40.
I've not seen a code set just because of a tire change, although I suppose that earlier indirect TPMS could - especially if you have severely mismatched tires that result in a substantial rotational difference? I'd be interested to know more on this one.
Sienna 2004...Just found out , the cel, vsc and trac off may come on if you change the air filter and disconnect the wire harness from the top of the filter housing. In this case it did throw air intake / mass airflow sensor codes.
My conclusion:
Any time you get a cel after disconnecting any wire harness while working on the engine,
it is a good idea to reset the cel first, and see if it is bogus, related to the disconnect before taking it to the dealer.
If there is a real problem, the cel will come back on.