By accessing this website, you acknowledge that Edmunds and its third party business partners may use cookies, pixels, and similar technologies to collect information about you and your interactions with the website as described in our
Privacy Statement, and you agree that your use of the website is subject to our
Visitor Agreement.
Comments
Maybe because of my height (6'), I don't have the reflections you speak of on the dash.
Longest trip I've taken in it was 3 hours one way. Obviously, we're talking about noise perception here, but I found the seats, noise level, comfort and ride to be very good. Not as good as my 300M, but the 300M isn't as fast and doesn't handle as well either. Noise level on take off gives a definitive growl, but once in cruising mode, it is quiet.
About the seats, I don't know if I'm considered "wide" or not (have a 36" waist), but I find the seats comfortable. I do agree that I would like more lateral support in the thigh area, though when I do aggressive driving.
Can't comment about the turning radius, because I haven't had a problem parking the PT. I'm able to manuever much better in the PT than in my 300M.
My MPG is 19 in town and 24 on the highway...dead on what the sticker said it would be. From what I've read on other BBs, once the PT has about 5K-10K miles on it, MPG will go up.
I will admit that my 0-60 numbers were derived on a semi-secluded road with no traffic. Trac control was off and I shifted using the auto stick, shifting at around 5,500 RPM. Letting the auto shift for itself, trac control on and just stomping on the gas yielded 0-60 in the high 6s. This was all done after "break-in".
The car is consuming one quart of oil for every 300-500 miles driven. Chrysler tried fixing it with a silicone seal to the baffle under the valve cover. No luck. Chrysler dealer did a dye test, but never pulled the engine apart to determine location of problem. Supposedly there are others out there that had their cars repaired at a different dealership and the dealership said the problem was improperly honed cylinder heads. Communication between Chrysler and their dealerships is very poor regarding tech support directives. Warranty paperwork has been sporadic at best, and Chrysler says that they are unaware of all the visits I've made to the dealership for this oil consumption problem, hence I am seeking help under the Lemon Law.
Please advise me ASAP if any of you have had problems with oil consumption and if so, has it been successfully remedied? And if so, how??? Have you had difficulties with your dealership and/or Chrysler?
Also, my air bag lite is on and won't go off.
I would like to advise others dealing with Chrysler to BE SURE to get all service and/or warranty paperwork at the time of each visit and make sure that it is accurate and describes exactly what was done at that visit -- mine doesn't!!! It is difficult dealing with Customer Service and Chrysler higher-up's after the fact.
My Lemon Law hearing is set for Tuesday 10/1/02. Any feedback regarding this issue would be very much appreciated!!
Thanks, Doug
The comment about the cruise/auto tranny down shifting going down hill. I actually like that feature. Going down very steep hills, the overdrive "kicks off" and I get commpression breaking while negotiating steep declines. That helps me immeasurably while negotiating steep roads.
However, it surprised me that the PT Cruiser gets almost as many ugly comments as the above vehicles. A large number of posters say it looks like a hearse. I think many people don't understand the retro styling. Any comments?
Comments...Sure!...those people are jealous!!
I will say this for the PT Cruiser, though--When it first came out I thought it was pretty cool, but would fade away as a fad. I guess I was wrong. People are still attracted to them. Like I mentioned a couple of posts ago, my mother-in-law just bought one and she says she has had many people these last couple of days ask her about it. There will always be people who have something bad to say about any car--what can you do?
I heard lemon law cases for 15 years. Documentation was very important to me. I found dealers were frequently either not writing repair orders or would return the car with something on the order of unable to duplicate or normal as their diagnosis.
For an oil use problem you should have been logging when you had to add oil so you can show how often and how many miles you could drive before having to add. Usually, as long as you have enough (the number depends on the state, four in my state) repair requests within the time period (and miles) your state allows for lemon law, the fact that no repair was made should not matter. In short, as long as you can document you gave the dealer enough chances (the repair orders) to fix the car, that the problem does exist (your log when you added oil and maybe receipts for oil purchased), and they didn't fix the car, you will be in a strong position.
If your documentation is weak, be sure to explain why.
So far, I agree communication from DC is weak. I called them twice, and e-mailed them also about my waterfall rear window washer (it weeps when not used, so there are water lines down the window all the time, and on the tailgate too - kind of like having a drippy faucet). It is now two weeks and they have not called nor e-mailed.
boaz47
You are correct in that it depends on what what one wants for a long trip car. For me, the P/T seats are on the small side, but still quite comfortable. The room is fine too. However, compared to my MDX and Avalon, or the Jag it replaced, the P/Turbo is noisier, doesn't ride as well, doesn't "feel" like it is as stable (it does corner a little better than the MDX) at high speed, doesn't have as strong an A/C, and has a very short range. That said, we love it anyway because it is a blast to drive. There is nothing wrong with it for trips, but, as you said, it depends on what one wants. I prefer the isolation of the other cars for long freeway drives.
graphicguy
The downshifting while the cruise control is on takes place on freeway hills where the car, if the cruise control is not in use, will slow by just easing a bit on the gas pedal while in overdrive. In my case it is an downshift that is not needed to maintain speed (or keep from speeding up). I agree with you that on very steep grades it would be a good thing, but I probably wouldn't be using cruise control on those.
The impression I have is that the cruise control is just a bit slow easing the throttle under some conditions as one crests a freeway hill. The result is the car speeds up about three mph and the downshift occurs, with third being held all the way down the hill. Where the initial down slope is less, and the cruise can hold the speed even as the car starts down the hill, the transmission will stay in overdrive even as the hill steepens to a greater slope than the one where it downshifts near the top.
As for the "retro" styling, maybe one has to be old enough? It was the retro look that caught our eye and the primary reason my wife wanted a P/T (and it was also the main reason she wanted the S-Type 4.0 Jag before the P/Turbo) - note: the P/Turbo is much more fun to drive than the Jag.
I am amazed at the amount of junk that I can haul in such a compact package. I have had the rear seats out a few times (something I would never have done in my van) and have had the back packed full.
I notice the new TV ad stresses the flexibility and load carrying ability.
thanks
I increased the pressure from the 33-34 the car came with to 38. Didn't notice any difference in ride, but the turn in seems sharper with the higher pressure. I wonder if your better starting traction is due to lower tire pressure. Probably the road rather than the tire pressure, but I wonder.
Notes: Car remains tight and rattle free at 1500+ miles. Only real problem has been the weeping rear washer. I installed an in line check valve the dealer gave me over the weekend and hope this stops the weeping. Speedometer is accurate according to mile markers on the road. Drove it for 150 miles yesterday and found the seats okay, though they could use more side support for me, My wife finds them fine. Had to raise the headlight aim some - helped a lot.
Mpg has gotten a little better on the highway. Now 22-23 with A/C on and at the high SoCal freeway speeds. Local mpg staying in the mid teens. A/C, in town stop and go, remains weak, but improves to okay when recirculate is used. Works well enough on the highway. Reflections in windshield are much less if I scrunch a down in the seat, so it appears that those of us that sit tall in the saddle (the seat is all the way down) see glare and such while those that sit "shorter" don't.
The charts shown in the service manual are for a low engine speed (like being caught in stop and go traffic). Maybe the turbo has a higher underhood temperature at low speeds and that reduces A/C efficiency?
The service manual seems to confirm my impression that my turbo's A/C isn't so great in warm day, low speed, stop and go traffic.
A/C performance could very well be affected by the higher temps of the turbo engine. It's just not been a problem for me in the OH valley. I'm sure that the temps here aren't as consistently as hot as it is in TX.
You have about the same mileage as I have. I've not driven my PT GT very much (1,400+ miles in two months) because of having 4 cars and only two drivers. That'll change given the fact that I've decided to get rid of some of the "fleet" that's been sitting in my garage and in my driveway.
I should check my mileage. I checked it when I first got it and it was dead on what the sticker said. I'll probably check it next fill-up.
Thanks for your input.
www.zainobros.com
I've been using it for years and have yet to find anything better.
I have seen a couple of mentions of this on other forums, but no one has indicated a fix or resolution after their first post explaining the SAME problem I am having. Any one have any ideas??? Thanks again.
Hi all, just bought a 2002 Limited 5 speed with 6000 miles. Love the car so far, but have noticed a strange thing. When creeping up at a drive thru, or traffic light, the RPMs go up over 2000, then back to about 1000. You know, when you slightly give gas, and let out the clutch, then back in with the clutch and off the gas...the rpms should drop back to idle speed, about 800-900rpm or so, but instead, they climb to 2000 first. BTW, this is with a warm engine, haven't noticed it with cold engine. Anyone else experience this and have a fix? Dealer say "normal" yea right!
thanks for any help, Jeff
window wipers....the solution to that problem is to take a 1/4 inch drill bit and drill a hole in the cap of your window washer fluid tank...that has been the fix for some time now (2 years).
Also....I never found the problem with my cruiser leaking so darn much oil on the garage floor....no it wasn't the filter or oil pan bolt...I wasn't about to go through the hassle with Chrysler in court....sooooo I traded it in last weekend.....
I will say this...It is one of the nicest looking cars out there....my wife and I drove it the first year June 2000 from Lancaster to Yellowstone
and of course the Tetons and beyond...5,317 miles to be exact. It did a great job pulling the mountains and protecting us from bears in the park.....I never did get use to all the road noise....at times we would have to yell to each other (not a joke)...that was frustrating...checked the gas mileage twice on that trip....highest was 28.8 and 27.7....thought that was pretty good considering all the hills etc.....hated filling up with gas all the time though....(small tank)..the other thing that really bugged me was the rpms at 70 mph...something like 3000 plus rpms?...anyway we have some wonderful photos with that car....was kinda comfy....and the guy that posted his concern about the reflection in the window from the dash is 100% right on....it is the worse I've ever seen..You can't beat the rear seats for room and comfort in such a small pkg....anyhow...thanks for listening in and I wish all of you fun in your PT's.....
GOD Bless America
Mine is a rear washer that weeps. The tank vent on mine is a wide slot in the tank neck tread area and is wide open. Even tried with the cap off. Rear washer still dribbled. Chrysler no help at all. Fixed by installing a check valve in line at the nozzle.
Maybe noise insulation is better on my turbo. While it certainly is not quiet at high freeway speeds, I wouldn't call it loud either. I'd like it quieter too, but conversation hasn't been a problem.
I do wish that it had a larger gas tank, though.
I am familiar with the rpm increases with A/C use, and defroster use (I am VERY familiar with A/C, but what's a defroster? I live in Southern AZ! LOL)
This condition I expalin (perhaps I didn't explain it well) doesn't seem like that at all..in fact, the rpm goes up to 2000-2100 when the clucth is depressed and the gas pedal released suddenly, as I inch up at a left turn, or backing out of a parking space in the mall. It really deosn't seem to be a matter of the load being released from the engine, but rather an electronic control increasing the rpm. The funny thing is, if the vehicle is stopped, it doesn't do it, but anything over about 2mph, it will.
Example: If I slightly depress the gas pedal from ilde, say to 1200-1500 rpm, and release while the vehicle is stopped, the rpm increases and decreases relative to pedal (as it should), but if the car is moving slightly, with this same test, after I release the gas pedal at 1200-1500 rpm, the rpm will increase to 2100 first, before decreasing. Could it be related to some sort of vehicle speed sensor? This condition is only with a warm engine, I have not been able to duplicate it with a cold engine.
I saw a post on another PT forum with a 5 speed driver mentioning being irritaded with the same conditon, and another 5 speed driver (also apparently, a certified mechanic) replying that it wasn't normal, and may be the MAP sensor, as DC is noted for bad map sensors? I have tried to get replies from them to see if it has been corrected, to no avail, yet.
If you get a chance to try to duplicate this, I would be happy to hear if yours does it, or not. thanks,
Sorry for long post,
Jeff
I have an autostick and my RPMs are consistently ~700RPM at idle, maybe a little above that with the A/C compressor on.
What do you think? ;-)
Revka
Host
Hatchbacks & Wagons Boards
Take a look under the rear of your Turbo. Is the Rear Stabilizer Bar, that the window sticker says is standard, actually there. Mine has no rear stabilizer bar.
The service manual shows a rear bar and says some models may have one in addition to the torque tube inside the rear axle.
Apparently Chrysler is now reporting that the suspension for 2003 has been drastically revised and that the rear sway bar is now redundant. The Window sticker has not yet been revised to reflect that. A similar situation arose when Chrysler went from "Chrome" to "Chrome Clad" wheels.
That said, consider discussing the matter with your dealer. With the amount of interest generated recently, they may have gotten more information.
The rear suspension hasn't been "drastically" revised. Tweaked some, yes, but it is still essentially the same twist beam rear the P/Ts started with about three years ago. The rear axle has a torque tube running through the axle that does the same thing as a stabilizer bar.
To me, it appears that for all practical purposes, because they do the same thing, the torque tube can be thought of as an internal rear stabilizer bar. A small adjustment in the size of the torque tube can make the external rear stabilizer bar unnecessary to achieve the desired roll resistance.
According to the parts people there is a different torque tube for cars that have a rear stabilizer bar. The service manual shows the rear stabilizer bar and gives instructions for installation and removal.
I wonder how the car will handle with more rear roll resistance. It would be nice to have less "lean."
To me, it's Chryser's mistake and someone is probably going to take heat in Auburn Hills over the omission.
I also spoke to my dealer. They are aware of the "faux pax" and asked me to come into the dealership. They said they'd put the sway bar on (if you look, the area where it's supposed to be installed still has the holes drilled for attachment), they would. They said that I could drive a "loaner" that has the sway bar attached. If I could tell the difference, they would go ahead and install it. If I couldn't tell the difference, they agreed to offer service or accesories that would be equal in price to the cost of the sway bar and installation...figure it's got to be a couple hundred bucks.
I'll let you know what I find out.
Although, I'm not thrilled with the mistake, they seem to be doing everything they can to make me happy.